
How to Write a HACCP Plan for a Dip, Sauce or Spread Plant (2026 Guide)
A plain-language walk through the 7 HACCP principles and 12 Codex steps, applied to refrigerated dips, sauces and spreads, with a worked example and the packaging-line controls that belong in your plan.
A HACCP plan is a written food safety document that identifies the biological, chemical and physical hazards in your process, decides which steps need a control, sets measurable limits, and defines monitoring, corrective actions, verification and records. For a refrigerated dip, sauce or spread plant, the plan follows the process from receiving to dispatch, with special attention to Listeria in ready-to-eat areas, allergen cross-contact, metal and temperature control. This is general guidance, not regulatory advice.
- Primary framework
- 7 HACCP principles, 12 Codex steps
- US regulation
- FSMA Preventive Controls, 21 CFR Part 117 (PCQI)
- Canada
- SFCR preventive control plan (PCP)
- Cold-holding reference
- At or below 41°F / 5°C
- Fill-weight accuracy
- ±0.5% (servo-driven volumetric piston)
- Sanitation features
- CIP option, tool-free strip-down, 304 stainless
- Plan sign-off
- Qualified person (PCQI in the US)
What a HACCP plan is and why dip and spread plants need one
A HACCP plan (Hazard Analysis and Critical Control Points) is the written record of how your plant keeps a specific product safe. It names the hazards that could reasonably occur, the steps where you control them, the limits that must be met, and the evidence you keep to prove it. Writing a HACCP plan is less about paperwork and more about forcing a disciplined walk through your process, from the raw chickpea or herb delivery to the pallet leaving the dock.
Dips, sauces and spreads deserve their own careful plan because they are usually ready-to-eat, refrigerated and eaten without a cooking step by the consumer. If you are earlier in the journey, start with our guide on how to start a hummus business, then return here.
HACCP, FSMA Preventive Controls and Canada's SFCR: how they fit together
HACCP is an internationally recognized method, set out in the Codex Alimentarius General Principles of Food Hygiene. Regulators do not all use the same label for it, so it helps to know how the main frameworks relate.
- United States. Most registered food facilities fall under the Current Good Manufacturing Practice, Hazard Analysis and Risk-Based Preventive Controls rule, 21 CFR Part 117. It requires a written food safety plan prepared or overseen by a PCQI, containing a hazard analysis and risk-based preventive controls, plus monitoring, corrective actions, verification, a recall plan and records. FDA explains the rule on its FSMA preventive controls for human food page.
- Canada. The Safe Food for Canadians Regulations (SFCR), enforced by the CFIA, require most food businesses to have a preventive control plan (PCP) that identifies hazards and the controls for them, with written plans and records for many operators.
- Other markets. Plants selling into the UK or EU should confirm local requirements; both rely on HACCP-based food safety management systems.
The practical point is that a Codex-style HACCP plan is a strong foundation for each of these. The main vocabulary difference is that FSMA speaks of preventive controls, of which only some are critical control points. Process controls, allergen controls, sanitation controls and supply-chain controls are all preventive controls under Part 117. Which of them need a critical limit, monitoring and verification at the same strictness as a classic CCP is a decision for your PCQI, based on your hazard analysis. Our certifications and compliance page explains what our machine supports and what remains your plant's responsibility.
The 7 HACCP principles in plain language
Every HACCP plan, however large, is built on the same seven principles. For a dip or spread plant they translate like this.
- Conduct a hazard analysis. For each step, list biological hazards (Listeria monocytogenes, Salmonella, pathogenic E. coli), chemical hazards (allergens, cleaning-chemical residue) and physical hazards (metal, glass, plastic). Decide which are significant enough to need control.
- Determine the critical control points. Identify the steps where control is essential and where a failure cannot be corrected later, such as a validated cook, a metal-detection step or cold storage.
- Establish critical limits. Set a measurable boundary for each control: a minimum temperature, a maximum time, a detector sensitivity, a pH ceiling.
- Establish monitoring. Define who checks, what they check, how often and with which calibrated instrument.
- Establish corrective actions. Decide in advance what happens when a limit is missed: hold product, investigate, fix the cause and document it.
- Establish verification. Prove the system works through calibration, record review, environmental swabbing, finished-product testing and periodic review of the whole plan.
- Establish documentation and record-keeping. Keep the plan, the monitoring records, the corrective-action records and the verification records, signed and dated.
The 12 steps to write a HACCP plan (Codex sequence)
Codex presents the work as twelve steps: five preliminary tasks, then the seven principles above.
- Assemble the HACCP team from production, sanitation, quality, maintenance and packaging, plus a PCQI or outside expert if needed.
- Describe the product: formulation, measured pH and water activity, packaging, storage temperature, shelf life.
- Identify intended use and consumers: ready-to-eat, refrigerated, including vulnerable groups.
- Construct the flow diagram from receiving to dispatch, including rework loops.
- Confirm the flow diagram on site while the line runs.
- Conduct the hazard analysis (principle 1).
- Determine the critical control points (principle 2).
- Establish critical limits (principle 3).
- Establish a monitoring system (principle 4).
- Establish corrective actions (principle 5).
- Establish verification procedures (principle 6).
- Establish documentation and record-keeping (principle 7).
Get a configured SDH-R quote for your productSend your product, cup size and target cups per minute — we reply within 24 hours.
Request a quoteTypical hazards in a refrigerated dip, sauce or spread plant
Your own hazard analysis decides what is significant, but these hazards come up in almost every ready-to-eat dip and spread operation.
Listeria monocytogenes
Listeria survives refrigeration and thrives in wet, cool plant environments, which describes most dip rooms. The usual route into product is not the raw ingredient but post-process contamination: drains, condensate, wheels, hoses and any surface touching product after the cook or blend. Controls are sanitation, hygienic zoning, equipment that can be taken apart and cleaned, and an environmental monitoring program used as verification.
Allergen cross-contact
Sesame (tahini) is a major US allergen, joining the list on January 1, 2023 under the FASTER Act. Milk (tzatziki, labneh, cream cheese, queso), tree nuts (pesto, nut butters), soy and eggs (aioli) are common on the same site. Controls include scheduling, validated allergen cleaning, dedicated tools and label verification. Our food labeling requirements guide covers how allergens must appear on pack.
Metal fragments from grinders, mills and fillers are controlled by detection downstream of the last metal-contact point. Temperature abuse and seal failure are controlled through cold-chain monitoring and seal-integrity checks.
Worked HACCP plan example: refrigerated hummus line
The table below is an illustrative HACCP plan example for a refrigerated hummus or similar dip line. It is a teaching aid, not a template to copy. Where a limit is not a widely recognized standard, it says so: you must set and validate your own limit with your PCQI or process authority, based on your recipe, equipment and shelf life.
Illustrative hazard analysis and control summary, refrigerated hummus (example only, not a validated plan)
| Process step | Hazard | Control | Critical limit / monitoring |
|---|---|---|---|
| Chickpea cooking | Survival of vegetative pathogens | Cook step, if validated as a kill step | Set and validate your own time/temperature; log each batch |
| Cooling and holding of cooked product | Pathogen growth, recontamination | Controlled cooling, covered or closed transfer | Set and validate your own cooling limits; monitor temperature and time |
| Blending with tahini, lemon, garlic | Allergen cross-contact (sesame, others), acidity out of range | Allergen scheduling and cleaning; formulation control | Verify pH and formulation per recipe; set and validate your own pH limit |
| Filling cups | Post-process Listeria, fill-weight error, product on flange | Sanitary filler, validated cleaning, weight checks | Check weight at set intervals against declared net content; sanitation verified by swabs |
| Sealing and lidding | Seal failure, contamination, tamper evidence | Seal parameter control, visual and leak checks | Set and validate seal temperature, pressure and dwell; check seals at set intervals |
| Metal detection or X-ray | Metal fragments | Detector downstream of last metal contact | Test with certified test pieces at start, set intervals and end; hold and re-inspect on failure |
| Cold storage and dispatch | Temperature abuse, pathogen growth | Refrigeration, logger checks | At or below 41°F (5°C) as a common cold-holding reference; confirm against your product and market rules |
Notice what the table does not say. It does not claim every row is a critical control point. Some rows are process controls, some are sanitation or allergen controls, and some are verification activities. How you classify them is a decision recorded in your hazard analysis, not something a template can make for you.
Where packaging equipment fits in your HACCP plan
The filling and sealing line is where product is most exposed, so equipment design directly affects how easy your controls are to run. Our SDH-R automatic rotary cup filling, sealing and lidding machine is designed to support plants operating under HACCP, FSMA, BRCGS or SQF programs. It is not itself "HACCP certified", and no machine can be: the plan belongs to your plant. Here is where the machine helps your controls. Sanitary features are detailed on our technology page.
- Sanitation and CIP. Food-grade 304 stainless construction, tool-free strip-down and an optional clean-in-place system make validated cleaning faster to perform and easier to repeat. Your sanitation SOP and its verification stay your responsibility.
- Allergen changeover cleaning. Recipe storage in the HMI keeps SKU changeovers under roughly 15 minutes mechanically, but a changeover between a sesame product and a sesame-free product needs your full validated allergen clean on top of that. Do not treat a fast mechanical changeover as a cleaned one.
- Fill-weight checks. The servo-driven volumetric piston filler holds ±0.5% fill accuracy, and an optional weight checker with a feedback loop gives you a documented check and an automatic correction.
- Seal checks. Roll-film membrane sealing gives a heat-sealed, tamper-evident closure. Seal temperature, pressure and dwell are the parameters you validate and monitor; our cup sealing machine guide explains them.
- MAP as a quality measure. The optional nitrogen flush brings residual oxygen down to 0.3-0.4% and can extend refrigerated shelf life from roughly 7-10 days to 30-45+ days, depending on the product. It slows spoilage; it is not a kill step and does not replace cold-chain control or Listeria controls. See our MAP nitrogen flushing guide, and confirm your actual shelf life through the testing described in our shelf-life testing guide.
Records, verification and reassessment
A plan that is not backed by records does not exist in the eyes of an auditor or an inspector. Plan the paperwork at the same time as the controls.
- Monitoring records. Real-time entries made by the person who did the check, with time, value and initials, not end-of-shift reconstruction.
- Corrective-action records. What failed, which product was held, root cause, release decision and who made it.
- Verification records. Instrument calibration, metal-detector challenge results, swab results, record reviews, finished-product tests.
Plans also need scheduled reassessment. Under 21 CFR Part 117, the food safety plan must be reanalyzed at least once every three years, and sooner whenever something changes that could affect hazards: a new ingredient, a new supplier, new equipment, a new recipe, a customer complaint trend or a positive pathogen finding. Adding a new filler or a nitrogen-flush station is exactly the kind of change that triggers a review.
Common HACCP plan mistakes in food manufacturing
- Copying a template unchanged. A HACCP plan template is a layout, not an analysis. Your equipment, recipe and layout produce different hazards.
- Treating every step as a CCP. Too many CCPs dilute attention. Use the hazard analysis to separate true critical controls from good manufacturing practice.
- Unvalidated limits. A limit taken from a forum or a competitor has no scientific support for your product. Validate it.
- Ignoring post-process contamination. The cook is not the biggest risk in a dip plant; the open filling area is.
If a new line is part of your plan, bring the packaging questions to the table early. Send us your product, cup size and target cups per minute through our contact page, see the hummus filling machine configuration, and we will reply within about 24 hours. You can also request a quote once your plan scope is clear.
How to Write a HACCP Plan for a Dip, Sauce or Spread Plant (2026 Guide) — Frequently Asked Questions
A HACCP plan is a written food safety plan that identifies the biological, chemical and physical hazards in a specific process, determines which steps require control, sets critical limits, and defines monitoring, corrective actions, verification and records. For a dip, sauce or spread plant it follows the product from receiving to dispatch. It should be developed and validated by a qualified person.
The seven HACCP principles are: conduct a hazard analysis, determine critical control points, establish critical limits, establish monitoring procedures, establish corrective actions, establish verification procedures, and establish documentation and record-keeping. Codex Alimentarius adds five preliminary steps before them, giving the familiar 12-step sequence used to write a plan for a food manufacturing plant.
Not exactly. A HACCP plan is the Codex method. The US FSMA rule, 21 CFR Part 117, requires a food safety plan with a hazard analysis and risk-based preventive controls, prepared or overseen by a PCQI. A HACCP-based plan is a strong foundation, but FSMA also covers allergen, sanitation and supply-chain controls and a recall plan, so confirm your plan meets Part 117.
Under the Safe Food for Canadians Regulations, most food businesses that need a licence must have a preventive control plan that identifies hazards and the controls for them, with written plans and records required in many cases. Requirements depend on your activities and whether you trade across provincial or international borders, so check with the CFIA and a qualified advisor for your situation.
There is no single answer, because it depends on your process and hazard analysis. Common candidates are a validated cook step, metal detection or X-ray, and cold storage. Many dip plants also run sanitation, allergen and environmental controls as preventive controls rather than CCPs. Your PCQI or HACCP team should document and justify each classification in your hazard analysis.
Nitrogen flushing with the SDH-R lowers residual oxygen to 0.3-0.4% and can extend refrigerated shelf life from roughly 7-10 days to 30-45+ days, depending on the product. It is a quality and shelf-life measure, not a kill step. It does not replace cold-chain control, sanitation or Listeria controls, so treat it separately in your plan.
The SDH-R uses food-grade 304 stainless steel, tool-free strip-down and an optional CIP system, so parts are accessible for cleaning, and its HMI stores recipes so mechanical SKU changeover takes under roughly 15 minutes. Your validated allergen cleaning procedure, for example moving from a sesame to a sesame-free product, remains your plant's responsibility and takes longer than the mechanical changeover.
No. Your HACCP or food safety plan must be written and validated by your own team with a qualified person, such as a PCQI in the US. We can supply equipment information on cleaning, fill-weight accuracy, seal parameters and MAP, which your team can reference. Contact our engineering team through the quote form for the technical details your plan needs.
Related machines & guides
Explore the pages most relevant to this application.
Why producers buy from Hummus Pack
Ready to Automate Your Filling Line?
Get a personalized SDH-R configuration and price for your product, cup sizes, and production volume.