
Refried Beans Filling Machine for Bean Dip Cups and Tubs
Fill refried pinto beans, black bean dip and layered bean dip bases into pre-formed cups and tubs, then seal them in the same rotation. A servo piston meters sticky bean paste from 50 to 500 g at ±0.5%.
A refried beans filling machine deposits a set weight of thick, starchy bean paste into pre-formed cups or tubs, then seals them. The Hummus Pack SDH-R works on an indexing rotary turret: a servo-driven volumetric piston fills 50-500 g at ±0.5%, a heat-sealed membrane closes the cup, and two optional extra fillers add salsa, sour cream or guacamole layers. Bean products typically run 18-25 cups a minute; pricing starts at $45,000 USD.
- Best fit
- Refrigerated refried beans, bean dips and bean pastes in pre-formed cups and tubs
- Fill range
- 50 g - 500 g (approx. 2-17 oz) standard
- Accuracy
- ±0.5% (servo-driven volumetric piston)
- Output
- 18-25 cups/min real-world; up to 30 on a dry cycle
- Fillers per pass
- Up to 3 (bean base plus two layers or toppings)
- Changeover
- Under ~15 minutes between SKUs
- Price
- From $45,000 USD (single filler)
What a Refried Beans Filling Machine Does on a Cup Line
A refried beans filling machine meters cooked, mashed bean product into a pre-formed cup or tub and closes it, so each pack leaves sealed and ready for the cooler. Our SDH-R handles refrigerated refried pinto beans, black bean dips, bean pastes and the bean layer of layered dips. Each cup is denested onto the turret, filled by a servo-driven volumetric piston and heat-sealed with film cut from a roll; a nitrogen flush and snap-on lid are optional. The complete machine is on our SDH-R product page.
Beans sit at the heavy end of what we fill. Smooth refried beans behave more like a stiff paste than a dip, so our paste filling machine guidance applies too, while our dip filling and sealing machine hub covers the wider dip family. This page covers what beans do inside a refried beans filling machine and how we configure the SDH-R around them.
Viscosity and Stickiness: How a Bean Filling Machine Meters Thick Paste
Refried beans get their body from gelatinized starch, mashed skins and often lard or oil. The result is a yield-stress material: it holds a peak until pushed hard enough, then flows, and it clings to stainless steel. Gravity fillers barely move it.
A servo-driven volumetric piston suits that behavior: it draws a fixed volume into its cylinder and pushes it out positively, so the deposit does not rely on the paste flowing by itself. Stroke speed is saved per recipe on the HMI, so a stiff refried bean and a looser black bean dip each run with their own profile.
Air pockets: the hidden cause of light cups
Most short-weight bean cups trace back to trapped air. Stiff paste bridges over the hopper outlet and leaves a hollow that the piston partly fills with air on its intake stroke. Practical controls:
- Keep the hopper topped up so the paste head stays steady instead of tunneling.
- Slow the intake stroke for stiff recipes so the cylinder fills completely.
- Add the optional weight checker with feedback loop, because a volumetric filler cannot see density changes caused by air or a shift in fat content.
Bean Paste Filling Machine Nozzles: No Tails on the Flange
Sticky starch pastes string. When the piston stops, a tail of bean paste can hang from the nozzle and drop onto the cup rim as the turret indexes. A smear of bean on the flange, especially from a lard-based recipe, stops the sealing film from fusing to the cup, and the weak seal turns up later as a leaker in a retail case.
We choose between two nozzle styles on your actual product:
- Cut-off nozzle. A valve closes across the product column at the end of the deposit. It suits stiff, smooth refried beans that tear cleanly rather than drip.
- Suck-back nozzle. Product is drawn back up the nozzle after the stroke, so nothing falls during the index. It suits softer bean dips that would otherwise hang a droplet.
Nozzle diameter, height above the cup and stroke profile are set at commissioning so the deposit lands centered, leaves headspace and clears the rim. Seal temperature, pressure and dwell are then tuned to your film and cup; with fat-rich beans, a clean flange does more for seal integrity than a hotter seal bar.
Fill Temperature on a Refried Beans Filling Machine
Refried beans change with temperature more than most dips. Warm from the kettle they spread easily; chilled, the starch firms, the fat sets, and the paste can become too stiff to draw cleanly into a piston. Some plants fill warm; others cook, chill and fill cold.
We do not rate the SDH-R as a hot-fill machine and do not publish a maximum fill temperature. It is specified for fresh and refrigerated products filled at a pumpable temperature, and the right temperature for your recipe is agreed with our engineering team before we quote. We work through:
- How stiff your beans are at the temperature they actually reach the hopper, including after a line stop.
- Whether a warm deposit will leave condensation under the membrane once the cup is chilled.
- How your validated cooling step brings sealed cups down to refrigeration temperature, which is a food safety control in your plan rather than a machine setting.
If your process depends on filling hot, talk to our engineering team before you budget for a refried beans filling machine.
Get a configured SDH-R quote for your productSend your product, cup size and target cups per minute — we reply within 24 hours.
Request a quoteWhole-Bean, Chunky and Black Bean Dip Filling Machine Setup
Not every bean product is smooth. Rustic refried beans keep half-mashed beans, and black bean dips often carry corn, peppers or jalapeño pieces. For these, the SDH-R uses large-bore valving that passes particulates without squeezing them through a narrow gap. Whole beans can still split at the valve, so piece size and acceptable breakage are confirmed in trials before we quote.
Bean product versus recommended SDH-R setup
| Bean product | Filling behavior | SDH-R setup |
|---|---|---|
| Smooth refried pinto beans | Stiff, sticky yield-stress paste that firms as it cools | Servo piston with slow intake stroke, cut-off nozzle, agreed fill temperature |
| Chunky or rustic refried beans | Half-mashed beans and skins can block narrow passages | Large-bore valving and wider nozzle; piece size confirmed in trials |
| Black bean dip | Softer and looser; may carry corn or pepper pieces | Piston with suck-back nozzle; large-bore valving if pieces are present |
| Cheesy or creamy bean dip | Fat and dairy smear easily onto the flange | Suck-back nozzle, controlled fill height, seal settings tuned to the film |
| Layered bean dip base | Firm bottom layer that must stay level under the toppings | Piston base fill, then a second and third filler for the upper layers |
| Sweet bean paste (e.g. adzuki) in tubs | Very dense and tacky | Piston with tuned stroke; viscosity and fill weight confirmed with engineering |
Layered Bean Dip: Up to Three Fillers in One Pass
Layered bean dip is where a multi-component rotary machine earns its floor space. The SDH-R carries up to three fillers, so a cup gets a bean base and two further layers before sealing:
- Bean base. The volumetric piston lays down refried beans as a level bottom layer.
- Second layer. A second filler adds a spoonable layer such as sour cream, guacamole or salsa.
- Topping. A garnish filler drops sliced olives or diced tomato, or a peristaltic pump adds a hot sauce drizzle.
- Seal and lid. The cup is heat-sealed, optionally nitrogen-flushed and lidded.
Be realistic about the classic seven-layer dip: three fillers means three components per pass, so a practical plan is to fill the three layers that define the product or pre-blend two. Shredded cheese does not meter like nuts or seeds and is confirmed with our engineers first. A soft layer dropped onto a warm bean base can also sink or smear, one more reason fill temperature matters.
For the companion products, see our salsa filling machine, guacamole filling machine and sour cream filling machine pages, and our article on multi-component filling for layered dips and parfaits.
Refried Beans Packaging Safety: Listeria, Low-Acid Product and Reduced Oxygen
This is general guidance, not a food safety determination; your process authority decides formulation, shelf life and controls for each recipe.
Beans are a low-acid food. Refried beans and most bean dips sit well above pH 4.6, the line used to define low-acid foods in 21 CFR Part 113, and canned refried beans get their shelf stability from a scheduled thermal process carried out under that rule. A refrigerated cup has no kill step after sealing, so safety rests on cooking, hygienic filling, formulation, cold-chain temperature and a validated shelf life. Two hazards need particular attention:
- Listeria monocytogenes. It grows under refrigeration and settles into wet plant areas, so cooked beans can be recontaminated between kettle and seal. Health Canada's 2023 Listeria policy sorts ready-to-eat foods by whether they can support its growth, a question a moist bean dip should answer with data.
- Clostridium botulinum. A nitrogen flush makes the cup reduced-oxygen packaging, and low-acid food in reduced oxygen is a classic botulism concern. Some strains grow under refrigeration, so a longer chilled shelf life under MAP needs controls your process authority has validated, typically through challenge testing.
On the machine side, the SDH-R is food-grade 304 stainless steel with tool-free strip-down, and it seals every cup in the same rotation that fills it, shortening open exposure. It supports plants operating under FSMA Preventive Controls (21 CFR Part 117), Canada's Safe Food for Canadians Regulations, HACCP, SQF and BRCGS; it is not itself certified to any of them. Our guide to building a HACCP plan for dips, sauces and spreads walks through the hazard analysis.
Canned, Pouched or Cupped: Where This Bean Cup Filling and Sealing Machine Fits
Shelf-stable refried beans in cans or retort pouches need hermetic containers, a scheduled thermal process and a retort. The SDH-R does none of that: it is a bean cup filling and sealing machine for fresh and refrigerated cups and tubs, and the wrong choice for:
- Canned, retorted, aseptic or other shelf-stable refried beans.
- Foodservice bags, pouches and cans of bean paste, and tubs above the 500 g maximum fill.
- Single-serve cups below 50 g; a 2 oz cup is the practical floor.
- Single-SKU volume well beyond 30 cups per minute, where an inline line is the better buy; our rotary versus inline comparison shows where the crossover sits.
- Frozen bean products.
It fits regional and private-label bean brands, Mexican-style deli producers and co-packers running several bean and dip SKUs at moderate volume, in standard 4, 8, 10 and 16 oz round, square or rectangular cups, or custom sizes on matching change parts.
Allergen and Recipe Changeovers on a Bean Filling Line
Pinto and black beans are not priority allergens, but the products around them often are. Layered dips bring milk from sour cream and cheese, and a line that also fills hummus brings sesame from tahini, the ninth major US allergen since January 1, 2023. There is a label claim to protect too: vegetarian black bean dip should not follow lard-based refried beans without a full clean.
SKU changeover on the SDH-R takes under about 15 minutes with recipes recalled from the HMI. Crossing an allergen or dietary claim takes as long as your validated cleaning procedure. Tool-free strip-down and the optional CIP system shorten that work, and running plain beans before dairy-topped dips reduces full cleans. Where cross-contact cannot be ruled out in Canada, the CFIA sets out how cross-contamination statements may be used.
Refried Beans Filling Machine Price, Lead Time and Quote
As a refried beans filling machine, the SDH-R starts from $45,000 USD in single-filler form, which covers most refried bean and single-layer bean dip lines. A second or third filler for layered dips, nitrogen MAP, labeling, a CIP system, a weight checker or custom cup tooling each add to that figure. Delivery is 8-12 weeks after order confirmation, with a 12-month warranty. They are designed and built in Calgary, Alberta, and backed by our Alberta, New Jersey and California service centres for producers across the United States and Canada.
For a useful quote, tell us the bean product and recipe style (smooth, chunky, layered, lard or oil), the temperature you plan to fill at, cup size and fill weight, the cups per minute you need, and options such as MAP or lids. We may call to understand the application and usually reply within about 24 hours. Send us your bean filling project details, email sales@hummuspack.com, or phone +1 (888) 922-7271 on weekdays between 9:00 AM and 5:00 PM MDT.
Sources and review
Every SDH-R figure on this page is checked line by line against the SDH-R engineering specification, as set out in our editorial policy. The regulatory and food-safety notes rely on these official sources, which we checked when this page was last updated:
- eCFR: 21 CFR Part 117, Current Good Manufacturing Practice, Hazard Analysis, and Risk-Based Preventive Controls for Human Food
- eCFR: 21 CFR Part 113, Thermally Processed Low-Acid Foods Packaged in Hermetically Sealed Containers
- Health Canada: Policy on Listeria monocytogenes in ready-to-eat foods (2023)
- Justice Laws Website: Safe Food for Canadians Regulations (SOR/2018-108)
- CFIA: Allergen-free, gluten-free and cross-contamination statements
Regulatory information here is general guidance, not legal advice; confirm your obligations with the authority or a qualified advisor. Spotted something out of date? Email sales@hummuspack.com or call +1 (888) 922-7271.
Refried Beans Filling Machine — Frequently Asked Questions
The Hummus Pack SDH-R refried beans filling machine starts from $45,000 USD in its single-filler form, which suits smooth or chunky refried beans in one layer. Extra fillers for layered dips, nitrogen flushing, labeling, CIP, weight checking or custom tooling add cost. Delivery is 8-12 weeks from order confirmation, with a 12-month warranty.
The SDH-R is specified for fresh and refrigerated products filled at a pumpable temperature; we do not rate it for hot filling or publish a maximum fill temperature. Refried beans stiffen sharply as they cool, so the fill temperature for your recipe is agreed with our engineering team before quoting.
The SDH-R's servo-driven volumetric piston fills 50-500 g at ±0.5% because it displaces a fixed volume rather than waiting for paste to flow. With refried beans, the bigger risk is air trapped in the hopper or cylinder, which lowers weight without changing volume. A topped-up hopper, a tuned intake stroke and the optional weight checker with feedback loop control that.
The SDH-R can, within limits. Large-bore valving passes particulates such as half-mashed beans, corn and pepper pieces, and an optional garnish filler places chunky toppings on the surface. Whole beans can split at the valve, so piece size and acceptable breakage are confirmed in trials with our engineering team before we quote.
It places up to three components per cup in one pass: typically a refried bean base from the volumetric piston, a second layer such as sour cream, guacamole or salsa, and a garnish or liquid topping. A full seven-layer dip needs more components, so the practical options are to fill three defining layers or pre-blend two.
The optional nitrogen MAP flush on the SDH-R reduces residual oxygen in the cup to 0.3-0.4%, which slows oxidation and some spoilage. For low-acid refried beans, reduced oxygen also creates conditions your hazard analysis must address for Clostridium botulinum, so any extended refrigerated shelf life must be validated by your process authority. Our MAP cup filler page explains the flush.
No. Canned refried beans are a low-acid product sterilized by a scheduled thermal process in hermetic containers, and the SDH-R is not a retort or aseptic system. It fills pre-formed cups and tubs only, from 50 to 500 g, for fresh and refrigerated products. Pouches, cans, jars and tubs above 500 g need different equipment.
Switching between bean SKUs on the SDH-R takes under about 15 minutes, with each recipe's stroke and seal settings recalled from the HMI. A changeover that crosses an allergen or a claim, such as a dairy-topped dip to a vegan bean dip or lard-based to vegetarian beans, follows your validated cleaning procedure and takes longer.
Related machines & guides
Explore the pages most relevant to this application.
Why producers buy from Hummus Pack
Ready to Quote Your Refried Beans Filling Machine?
Get a personalized SDH-R configuration and price for your product, cup sizes, and production volume.