
Filling Machine Capacity: How to Size a Cup Filler for a Food Startup or Co-Packer
Size a cup filler from your own numbers: real cups per minute, net run hours, an uptime factor you set and changeover time. Worked examples use the SDH-R's 18–25 CPM production range and sub-15-minute SKU changeovers.
Filling machine capacity is how many sealed cups a machine actually produces in a shift, not its rated speed. Calculate it as real cups per minute × 60 × net run hours × an uptime factor you set, after subtracting cleaning and changeover time. The Hummus Pack SDH-R rotary cup filler has a 30 CPM dry-cycle ceiling, typically sustains 18–25 CPM in production and changes SKUs in under about 15 minutes.
- Rated ceiling
- Up to 30 cups/min (dry cycle)
- Production output
- 18–25 cups/min, product-dependent
- SKU changeover
- Under ~15 minutes
- Fill range
- 50 g – 500 g (approx. 2 oz – 17 oz)
- Fill-weight accuracy
- ±0.5% (servo-driven volumetric piston)
- Fillers per pass
- Up to 3
- Starting price
- From $45,000 USD (single filler)
Filling Machine Capacity Starts With Real Output, Not Rated Speed
Filling machine capacity is the number of finished, sealed cups a machine delivers in the hours you actually run it. Most sizing mistakes start with a brochure speed multiplied by a full shift. Below is the arithmetic our engineering team uses when a food startup or co-packer asks whether one SDH-R rotary cup filler will cover its orders, with every assumption visible.
A dry-cycle rating is how fast the machine cycles its mechanics with nothing being dosed. Real output is the rate it sustains with your product in the hopper and film on the roll. The SDH-R's dry-cycle ceiling is 30 cups per minute (CPM); on real products it usually settles between 18 and 25 CPM, for four reasons:
- Product. Stiff hummus needs a controlled piston stroke so the dose breaks cleanly instead of tailing or trapping air, and thin salsa liquor pushed too fast splashes the flange, which weakens the seal.
- Cup size. A wide 16 oz tub has more product to settle and more flange to seal than a 4 oz cup.
- Fill weight. A 450 g dose needs a far longer piston stroke than a 60 g dose.
- Options. Extra fillers, nitrogen flushing, lid placement and coding each add a task that must finish within one index of the dial.
On an indexing rotary machine every station works on a different cup at once, so the dial moves only as fast as its slowest station. That is why real speed is a range confirmed in a trial, not a single number.
How to Calculate Machine Capacity: The Daily Cups Formula
Capacity math has two parts: how much of the shift is available for filling, and how many cups the machine makes in that time. The filling machine capacity formula:
- Net run hours = scheduled shift hours − cleaning and sanitation time − (number of changeovers × minutes per changeover ÷ 60).
- Cups per day = real CPM × 60 × net run hours × uptime factor. Real CPM × net run minutes × uptime factor gives the same answer.
- Cups per week = cups per day × production days per week.
What each input means:
- Real CPM: the sustained rate on your product, cup and options. Until a trial confirms it, pick a point inside the SDH-R's 18–25 CPM production range and note it.
- Cleaning time: set by your sanitation procedures, including allergen wash-downs between product families. CIP and tool-free strip-down shorten it, but your validated procedure sets the number.
- Changeover time: recipe recall on the HMI, change parts and purging the previous product. The SDH-R changes SKUs in under about 15 minutes; the examples plan a full 15 to stay safe.
- Uptime factor: a decimal between 0 and 1 that you set. It absorbs film roll changes, cup and lid replenishment, hopper refills, jams, rejects and any break not already deducted.
We do not publish a typical uptime figure, because it depends more on your crew, product and material supply than on the machine. Log every stop for a week on your current process or during a trial, divide productive minutes by planned minutes, then test the plan at a low and a high value.
Worked Example: From Cups Per Minute to Cups Per Day on a Startup Line
Take a small producer filling one hummus recipe in two flavors on a single shift. Apart from the SDH-R's published ranges, every input is an assumption:
- Assume an 8-hour scheduled shift, or 480 minutes.
- Assume 60 minutes of end-of-shift cleaning inside that shift.
- Assume one flavor changeover, planned at 15 minutes.
- Assume a real speed of 20 CPM, inside the 18–25 CPM production range.
- Assume an uptime factor of 0.85.
Net run time is 480 − 60 − 15 = 405 minutes, or 6.75 hours. Cups per day = 20 × 60 × 6.75 × 0.85 = 6,885. Over an assumed five-day week, that is 6,885 × 5 = 34,425 cups.
The shortcut many buyers start with, 30 CPM × 480 minutes, gives 14,400 cups a day. The realistic filling machine capacity is less than half of that, and nothing is wrong with the machine: the shift simply contains a wash-down, a flavor change and ordinary stops.
Packing Machine Capacity Scenarios With the Math Shown
The table runs the same formula across six situations for one SDH-R, with assumed inputs. Real CPM stays inside the 18–25 range except in the last row, the 30 CPM dry-cycle ceiling, shown for contrast only. Changeovers are planned at 15 minutes each.
Example daily capacity for one SDH-R (scenario inputs are assumptions; cups per day = real CPM × net run minutes × uptime factor)
| Scenario (assumed) | Real CPM | Scheduled min | Cleaning min | Changeover min | Net run min | Uptime factor | Cups per day (math) |
|---|---|---|---|---|---|---|---|
| Startup, 1 shift, 2 SKUs | 20 | 480 | 60 | 1 × 15 = 15 | 405 | 0.85 | 20 × 405 × 0.85 = 6,885 |
| Startup, 1 shift, 1 SKU, plain cup | 25 | 480 | 60 | 0 | 420 | 0.85 | 25 × 420 × 0.85 = 8,925 |
| Startup, 1 shift, 3 SKUs | 22 | 480 | 60 | 2 × 15 = 30 | 390 | 0.85 | 22 × 390 × 0.85 = 7,293 |
| Co-packer, 2 shifts, 8 SKUs | 18 | 960 | 120 | 7 × 15 = 105 | 735 | 0.80 | 18 × 735 × 0.80 = 10,584 |
| Co-packer, 2 shifts, 12 SKUs | 18 | 960 | 120 | 11 × 15 = 165 | 675 | 0.80 | 18 × 675 × 0.80 = 9,720 |
| Rated ceiling, no stops (not a plan) | 30 | 480 | 0 | 0 | 480 | 1.00 | 30 × 480 × 1.00 = 14,400 |
Going from 8 to 12 SKUs on the co-packer line costs 60 net run minutes, or 864 cups a day at 18 CPM and 0.80 uptime. The single-SKU startup beats the three-SKU startup by 1,632 cups a day: 1,071 from the higher speed (3 × 420 × 0.85) and 561 from the changeovers it avoids (22 × 30 × 0.85).
Get a configured SDH-R quote for your productSend your product, cup size and target cups per minute — we reply within 24 hours.
Request a quoteDemand Side: Forecasting Cups Per Week Before You Size the Machine
Capacity only means something against demand. Build the demand figure from orders you can see, then stretch it:
- Base weekly demand. For each retailer, distributor or food-service account, multiply delivery points × cases per week × cups per case, then sum the accounts. Use committed orders and a realistic pipeline.
- Peak season factor. Your busiest week divided by an average week, taken from your own sales history rather than a rule of thumb.
- Growth headroom. The growth you expect before the next equipment decision. With an 8–12 week delivery lead time from order confirmation, size the SDH-R for demand at least a quarter ahead.
- Required cups per week = base weekly demand × peak season factor × growth headroom.
Assume orders of 12,000 cups a week, a 1.3 peak factor and 1.5 times growth headroom (all assumptions): 12,000 × 1.3 × 1.5 = 23,400 cups a week.
One net run hour at 20 CPM and 0.85 uptime yields 20 × 60 × 0.85 = 1,020 cups, so 23,400 ÷ 1,020 = about 22.9 net run hours a week, or about 3.4 of the startup example's 6.75-hour net days. Against the 34,425-cup single-shift week, that is roughly 68% utilization, leaving room for a new account.
Run the formula backward for the speed you need: required real CPM = required cups per day ÷ (net run minutes × uptime factor). Comfortably under 25 CPM, one SDH-R fits; below 18 it simply runs fewer hours. Above 25, you are choosing between more hours, a second machine or a different class of line. To work through it together, send us your order forecast.
Cup Filler Sizing: Fill Weight, Cup Size, Extra Fillers and MAP
Each effect below is qualitative; the numbers for your SKUs come from a trial.
Fill weight and cup size
Larger doses inside the standard 50 g to 500 g range (approx. 2 oz to 17 oz) need longer piston strokes and more settling time before the sealer. A 2 oz portion cup sits at the low end of the fill range, and anything under 50 g falls outside it. If one line runs 4 oz cups and 16 oz tubs, give each SKU its own real CPM and weight the plan by how many of each you sell.
Fill accuracy is capacity too
Overfill is product you make and give away. Net contents checks under NIST Handbook 133 look at a lot's average and at how far individual packages fall short. FDA's net quantity rule, 21 CFR 101.7, recognizes only reasonable variations, and the CFIA's net quantity guidance explains how Canadian declarations are verified. The SDH-R's ±0.5% servo-driven piston lets you target closer to the label. An assumed 3 g average overfill across 6,885 cups is 20,655 g, about 20.7 kg given away every day.
Multi-component filling and MAP
The SDH-R can run up to three fillers in a single pass, for example a hummus base, an oil drizzle and a chickpea garnish; our multi-component filling guide covers the layouts. A topping slows the line only if it becomes the slowest station, which a centered garnish or a drizzle that must stay off the flange can do. Optional nitrogen flushing brings residual oxygen down to 0.3–0.4% but needs time to displace headspace air before sealing, so model multi-component and MAP cup filling SKUs toward the lower end of 18–25 CPM until a trial says otherwise.
Choosing a Cup Filler for a Food Startup or Co-Packer
Food startups: few SKUs, long runs
A startup fills a handful of its own recipes in long runs, so the main risk is sizing for a forecast that has not arrived. In the startup example, changeover takes 15 of 480 minutes (about 3%) and cleaning plus changeover 75 minutes (about 16%), so filling machine capacity planning is mostly about demand growth and uptime. A single-filler SDH-R starts from $45,000 USD on a 44 × 52 in footprint, with price scaling as you add fillers, MAP, labeling or custom tooling. Our small-batch cup filling guide covers this stage.
Co-packers: many SKUs, short runs
A co-packer sells line time to several brands, so SKUs per day dominate the math. In the eight-SKU scenario, changeovers take 105 of 960 minutes (about 11%) and cleaning plus changeovers 225 minutes (about 23%). Moving from a sesame-based hummus to a dairy tzatziki may need a validated wash-down, and the allergen controls in your food safety plan under 21 CFR Part 117 set that time, not the machine's changeover rating. Scheduling SKUs in allergen families keeps full washes rare.
If a contract needs 15,000 cups a day on that pattern, required real CPM = 15,000 ÷ (735 × 0.80) = about 25.5, just above the production range. The realistic answers are a third shift, fewer SKUs per day or a second machine. Our co-packer cup filling line page takes the contract filler's view, and brands weighing whether to fill at all can start with co-packer vs in-house production.
Hand Filling, Semi-Automatic, Rotary or Inline: Matching Cups Per Minute to Machine Class
With a required real CPM in hand, the machine class picks itself. We do not quote hand or semi-automatic speeds, which depend on the operator; time your own crew over a shift and use that figure.
- Hand filling suits recipe development and pilot batches. Output grows only by adding people.
- Semi-automatic: an operator places cups and a machine doses. It makes sense while labor is the cheaper variable; see our semi-automatic vs automatic comparison.
- Rotary automatic (SDH-R): cup feed, dosing, sealing and optional MAP and lidding on one dial. It fits when required real CPM is comfortably under 25, or when you need several SKUs, layered cups and quick changeovers.
- Inline: when one SKU needs more than 30 CPM, the SDH-R's rated ceiling, an inline machine built for long single-product runs fits better. Our rotary vs inline filling machine comparison shows where that break point falls.
Between 25 and 30 CPM is a gray zone: the mechanics can go there, but sustained production on most products will not. Plan more hours or a second SDH-R, which also adds redundancy, rather than counting on the ceiling all day.
Filling Machine Capacity Checklist Before You Request a Quote
Bring these inputs to a sizing conversation:
- Each product, with notes on viscosity, particulate size and filling temperature.
- Cup size, shape and fill weight for every SKU.
- Target cups per minute, or weekly demand and shift pattern for us to convert.
- SKUs per day and how they group by allergen.
- Options: extra fillers, nitrogen MAP, lid placement, labeling, coding or a weight checker with feedback loop.
- Current cleaning time and any uptime you have measured.
Send them through our quote request page; we reply within about 24 hours and may ask about the application before quoting. Service comes from our Alberta, New Jersey and California service centers. Specifications are on the SDH-R product page, and the cup filling and sealing machine cost guide shows how options move the price.
Sources and review
Every SDH-R figure on this page is checked line by line against the SDH-R engineering specification, as set out in our editorial policy. The regulatory and food-safety notes rely on these official sources, which we checked when this page was last updated:
- NIST Handbook 133: Checking the Net Contents of Packaged Goods
- 21 CFR 101.7: Declaration of net quantity of contents (eCFR)
- CFIA: Net quantity on food labels
- 21 CFR Part 117: CGMP, Hazard Analysis and Risk-Based Preventive Controls for Human Food (eCFR)
Regulatory information here is general guidance, not legal advice; confirm your obligations with the authority or a qualified advisor. Spotted something out of date? Email sales@hummuspack.com or call +1 (888) 922-7271.
Filling Machine Capacity — Frequently Asked Questions
Subtract cleaning and changeover time from the scheduled shift to get net run hours, then multiply real cups per minute × 60 × net run hours × an uptime factor you set. An SDH-R at an assumed 20 CPM, with 6.75 net run hours and an assumed 0.85 uptime factor, produces 6,885 cups a day.
Rated speed is a dry-cycle figure: how fast the machine cycles with nothing being dosed. Real output is what it sustains on your product, cup and options. The Hummus Pack SDH-R has a 30 CPM dry-cycle ceiling and typically sustains 18–25 CPM in production, so plan capacity from the real figure.
SKU changeover on the SDH-R runs under about 15 minutes, helped by recipe storage on the HMI, so plan a full 15 minutes per changeover. Allergen changeovers that need a validated wash-down are a separate, longer allowance set by your sanitation procedures; grouping SKUs by allergen keeps them to a minimum.
Use one you can defend from your own data. The uptime factor is the share of net run time in which the machine actually produces cups, after replenishment, hopper refills, jams and rejects. Log every stop for a week, then divide productive minutes by planned minutes. Our examples use 0.80 and 0.85 as assumptions, not benchmarks.
When a single SKU needs more than 30 cups per minute, the rated ceiling of the rotary SDH-R, an inline machine built for long single-product runs fits better. Between 25 and 30 CPM, extra shifts or a second SDH-R are usually safer than planning around the dry-cycle rating. Our rotary vs inline guide explains the break point.
They can. On the SDH-R, up to three fillers work on different cups at once, so an extra filler limits speed only if it becomes the slowest station. Optional nitrogen MAP lowers residual oxygen to 0.3–0.4% but needs time to displace headspace air. Model those SKUs toward the lower end of 18–25 CPM until a trial confirms your rate.
Not necessarily. The SDH-R starts from $45,000 USD as a single-filler machine, and delivery lead time is 8–12 weeks from order confirmation with a 12-month warranty. If your required speed is well below 18 CPM, it simply runs fewer hours, leaving room to grow. Send your numbers through our contact page for a sizing check.
Related machines & guides
Explore the pages most relevant to this application.
Why producers buy from Hummus Pack
Ready to Automate Your Filling Line?
Get a personalized SDH-R configuration and price for your product, cup sizes, and production volume.